se3a - se3m surface mount high efficient rectifiers prv : 50 - 1000 volts io : 3.0 amperes features : * high current capability * high surge current capability * high reliability * low reverse current * low forward voltage drop * fast switching for high efficiency mechanical data : * case : smc molded plastic * epoxy : ul94v-o rate flame retardant * lead : lead formed for surface mount * polarity : color band denotes cathode end * mounting position : any * weight : 0.21 gram maximum ratings and electrical characteristics rating at 25 c ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20%. symbol se3a se3b SE3D se3e se3g se3j se3k se3m unit maximum recurrent peak reverse voltage v rrm 50 100 200 300 400 600 800 1000 v maximum rms voltage v rms 35 70 140 210 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 300 400 600 800 1000 v maximum average forward current ta = 55 c i f(av) 3.0 a maximum peak forward surge current, 8.3ms single half sine wave superimposed on rated load (jedec method) maximum forward voltage at i f = 3.0 a v f 1.1 1.7 v maximum dc reverse current ta = 25 c i r 10 m a at rated dc blocking voltage ta = 100 c i r(h) 50 m a maximum reverse recovery time ( note 1 ) trr 50 75 ns typical junction capacitance ( note 2 ) c j 50 pf junction temperature range t j - 65 to + 150 c storage temperature range t stg - 65 to + 150 c notes : ( 1 ) reverse recovery test conditions : i f = 0.5 a, i r = 1.0 a, irr = 0.25 a. ( 2 ) measured at 1.0 mhz and applied reverse voltage of 4.0 v dc page 1 of 2 rev. 01 : january 10, 2004 rating i fsm 150 a smc (do-214ab) dimensions in inches and (millimeter) 0.305(7.75) 0.320(8.13) 0.245(6.22) 0.121(3.07) 0.115(2.92) 0.220(5.59) 0.012(0.305) 0.103(2.62) 0.280(7.11) 0.060(1.52) 0.260(6.60) 0.079(2.00) 0.006(0.152) 0.030(0.76) 0.008(0.203) 0.004(0.102)
rating and characteristic curves ( se3a - se3m ) fig.1 - reverse recovery time characteristic and test circuit diagram + notes : 1. rise time = 7 ns max., input impedance = 1 megaohm, 22 pf. 2. rise time = 10 ns max., source impedance = 50 ohms. 3. all resistors = non-inductive types. fig.2 - derating curve for output fig.3 - maximum non-repetitive peak rectified current forward surge current 0 25 50 75 100 125 150 175 1 2 4 6 10 20 40 60 100 ambient temperature, ( c) number of cycles at 60hz fig.4 - typical forward characteristics fig.5 - typical reverse characteristics 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 forward voltage, volts page 2 of 2 rev. 01 : january 10, 2004 60hz resistive or inductive load 2.4 1.8 1.2 0.6 3.0 100 10 1.0 120 0 150 0 90 60 30 0.1 10 80 0.01 0.01 1.0 0.1 100 140 0 20 40 60 120 percent of rated reverse voltage, (%) peak forward surge current, amperes average forward output current, amperes forward current, amperes reverse current, microamperes t j = 25 c t j = 100 c t j = 25 c pulse width = 300 m s 2% duty cycle 8.3 ms single half sine wave ta = 50 c se3a - se3g se3j - se3m d.u.t. oscilloscope ( note 1 ) 1 w 50 w 10 w 50 vdc (approx) pulse generator ( note 2 ) trr + 0.5 a 0 - 0.25 a - 1.0 a 1 cm set time base for 25-35 ns/cm
|